3005 (AW-AlMn1Mg0,5)

AlMn1Mg0,5 (AMG0,5)

Aluminum for food using.
Mechanical characteristics of Sheets - Properties :

 

Nominal chemical compound % (according to the standard EN 573-1):

 Si

 Fe 

 Cu

 Mn

 Mg 

 Cr 

 Zn 

 Ti

Others

 Al
Each
Total
0,6

0,7
0,30
1,0-1,5
0,2-0,6
0,1

0,25
0,1

0,05

0,15
Reste

 

Specific mechanical characteristics:

 

Sheets (according to the standard EN 485-2):
State
Specified thickness
Rm (MPa)
Rp0,2 (MPa)
A %
Bending radius
Hardness HBS
More than
Until
mini
maxi
mini
maxi
A 50
A
180°
90°
F
>2,5
80,0
115
-
-
-
-
-
-
-
-
O/H111

0,2

0,5

1,5

3,0

0,5

1,5

3,0

6,0

115

115

115

115

165

165

165

165

45

45

45

45
-

12

14

16

19

 

 

0 e

0 e

1,0 e

 

0 e

0 e

0,5 e

1,0 e

33

33

33

33
H12

0,2

0,5

1,5

3,0

0,5

1,5

3,0

6,0

145

145

145

145

195

195

195

195

125

125

125

125
-

3

4

4

5

-

1,5 e

1,5 e

2,0 e

 

0 e

0,5 e

1,0 e

1,5 e

46

46

46

46
H14

0,2

0,5

1,5

3,0

0,5

1,5

3,0

6,0

170

170

170

170

215

215

215

215

150

150

150

150
-

1

2

2

3

-

2,5 e

2;5 e

 

 

0,5 e

1,0 e

1,5 e

2,0 e

54

54

54

54
H16

0,2

0,5

1,5

0,5

1,5

4,0

195

195

195

240

240

240

175

175

175
-

1

2

2
-

-

1,0 e

1,5 e

2,5 e

61

61

61
H18

0,2

0,5

1,5

0,5

1,5

3,0

220

220

220
-

200

200

200
-

1

2

2
-
-

1,5 e

2,5 e

 

69

69

69
H19

0,2

0,5

0,5

1,5

235

235

-

210

210
-

1

1

-

-

-

73

73
H22

0,2

0,5

1,5

3,0

0,5

1,5

3,0

6,0

145

145

145

145

195

195

195

195

110

110

110

110
-

5

5

6

7

 

-

1,0 e

1,0 e

1,5 e

 

0 e

0,5 e

1,0 e

1,5 e

45

45

45

45
H24

0,2

0,5

1,5

0,5

1,5

3,0

170

170

170

215

215

215

130

130

130
-

4

4

4
-

1,5 e

1,5e

 

0,5 e

1,0 e

1,5 e

52

52

52
H26

0,2

0,5

1,5

0,5

1,5

3,0

195

195

195

240

240

240

160

160

160
-

3

3

3
-

 

-

 

1,0 e

1,5 e

2,5 e

60

60

60
H28

0,2

0,5

1,5

0,5

1,5

3,0

220

220

220
-

190

190

190
-

2

2

3
-
-

1,5 e

2,5 e

 

68

68

68

Top of the page

Properties (for infomation only):

 

Corrosion :
General corrosion index
Very good
Corrosion in sea atmosphere
Good
Corrosion under stress
Very good

Top of the page

Anodizing:
Bright anodizing
Satisfactory
Coloured anodizing
Good
Hard anodizing
Good
Protecting anodizing
Good

Top of the page

Strain, workability:
 
Annealing
Strain-aging
Cold working
Very good
Good
Deep stamping
Very good
Good
Strain by tension
Very good
Satisfactory
Embossing ability
Good
Satisfactory
Workability
Not recommended
Satisfactory

Top of the page

Welding:
Welding by electron beam
Very good
Gas welding 
Good
Arc welding
Very good
Spot welding
Good
Brazing
Very good
Soft brazing
Good

Top of the page

Physical and elastic properties:

Elastic
Physical
E
G
n
Tsol
Tliq
Cp
a
r
rel
l
EC
MPa
MPa
-
°C
°C
J kg-1 K-1
µm m-1 K-1
kg m-3
nW m
W m-1 K-1
%IACS
69500
26200
0.33
635
655
891
23.1
2730
41
160
42
Legend:
E 
 Elastic modulus MPa
G 
 Rigidity modulus MPa
 n
 Poisson's ratio  
Tsol 
 Solidification temperature °C
Tliq 
 Melting temperature °C
Cp 
 Specific heating J kg-1 K-1
a
 Ratio of temperature expansion µm m-1 K-1
r
 Density kg m-3
rel
 Resistivity nW m
l 
 Heat conductivity W m-1 K-1
EC 
 Electrical conductivity %IACS

 

Top of the page